Jump to content

arcadepcnut

Platinum Member
  • Content Count

    15
  • Joined

  • Last visited

Community Reputation

0 Neutral

About arcadepcnut

  • Rank
    Full Member
  • Birthday 06/25/1974

Contact Methods

  • Website URL
    http://www.biontek.com/breaktime

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. can someone please assist or point me to a forum or post? Here are my components: 24V power supply ledwiz 24v real pinball knocker car relay Here is what I THINK in need to do. Can someone please confirm or deny before I burn something up? I would like to get started on this on the weekend and need to map this out in my brain before I start. ledwiz to 86 on relay, 85 to common ground, 30 to 24v power supply, 87 or 87a to real 24v knocker. or better yet a picture.
  2. Hello all. Got everything ready to convert my virtual pin to LEDs and feedback with contactors. Also read the pinball 101 document and sorta have a handle on things. But I've got a few questions, I have a 12v supply for the LEDs. And a 24v supply for my 7 contactors and my knocker. The contactors I understand can run directly off the ledwiz and no need for a relay? My main question is how to wire the knocker. The knocker I know for sure I need a relay. I'm using the standard car relays. 87 87a 30 86 85 I'm just not sure how to wire it! It has the pins 30 which I think goes to my 24v power supply directly. 85 goes to ground. Here is the part I don't know. Does 87 or 87a go to the knocker? And 86 is my trigger from the ledwiz? Please help and offer some pointers. Will my 24v contactors need relays? I read they can just go one pin ground and the other 24v through the ledwiz so there is no lag. Wiring The relays confuse me.
  3. Good point. Thought I did. Thanks for pointing that out. So used to going to this forum for help with my Hyperpin cabinets!! Haha
  4. Hello all. Got everything ready to convert my virtual pin to LEDs and feedback with contactors. Also read the pinball 101 document and sorta have a handle on things. But I've got a few questions, I have a 12v supply for the LEDs. And a 24v supply for my 7 contactors and my knocker. The contactors I understand can run directly off the ledwiz and no need for a relay? My main question is how to wire the knocker. The knocker I know for sure I need a relay. I'm using the standard car relays. 87 87a 30 86 85 I'm just not sure how to wire it! It has the pins 30 which I think goes to my 24v power supply directly. 85 goes to ground. Here is the part I don't know. Does 87 or 87a go to the knocker? And 86 is my trigger from the ledwiz? Please help and offer some pointers. Will my 24v contactors need relays? I read they can just go one pin ground and the other 24v through the ledwiz so there is no lag. Wiring The relays confuse me.
  5. I got the lowres working. im fine with that. thanks
  6. same thing at 16bit. ill try the lowres and see what happens. i only have 512mb ram on my card.
  7. if this table comes up with white graphics chunks in the hires version with HR render on i assume i dont have enough video memory on my card? the framerate is fine. thank you
  8. Anyone figure out the script error. its just a generic script arguments error. no line number. It does this only if you replace the set controller to ultravp.backglassserv Try commenting out the line .SetDisplayPosition 1830, 460 like this '.SetDisplayPosition 1830, 460 Now not only can you move the DMD and it save it. You can use the UltraVP.BackglassServ with no script error
  9. Rawd: Could have sworn i tried the display 1 display2 and default settings. however just loaded star trek the next generation with pinmame set to default and i displays fine now! Wonderpuddle: no. i was just launching straight through VP9 frontend to eliminate as many variables as to why this was not working. Tried what you suggested. And it seems to be working except really really slow with the dmd on second monitor. soooo...Hyperpin is what launches the backglass unlike FP where it launches the backglass.....i see thank you for your help. Now i have to do some tweaking and should be good to go!
  10. I got FP working perfect on my cab with one screen the backbox set to 640x480 res and the LCD 24" playfield set to 1900x1280 res. everything plays beautiful except Blue vs pink wont even load. other than that excellent. There are a few key tables i really want to play. i read the VP forums and cant figure out what to do. i have had a 100% success ratio with help here. so here it goes some background. downloaded VP already scaled for cabinet tables from here http://www.hyperspin-fe.com/forum/showthread.php?t=2778 1 gig ram 3.4ghz processor 8800GT video 24" playfield 1900x1280 not rotated 17" backbox 1280x1024 not rotated .182 drivers fresh windows xp install nothing else loaded VP 9.0 and pinmame Primary monitor is the playfield secondary is backbox. backbox is located to the right of playfield in windows dual screen setup and extended not spanned. Cabinet.dll has been replaced with the one downloaded specifically for cabs. Problems: #1 The backbox does not show on second monitor. just the windows walpaper. I really want the backbox. The DMD is on the main playfield located horizontally (i.e. the wrong way for a cabinet). Dont want the dmd on the primary playfield but..... when dragged to the second monitor creates problem #2 #2 if DMD is on second screen it is either all black or frozen. the table either slows to a literal CRAWL or ceases to accept inputs at all. Basically every thing quits working till i drag DMD back to primary. #3 not really important but whne i quit VP it asks to go back to editor. i have no Q key on my cabinet. please help. if star trek next gen, T2 or Black knight we in FP i wouldnt even worry with this problem. Thanks in advance! Any help no matter how small is helpful
×
×
  • Create New...