liljohnnybravo Posted February 14, 2016 Posted February 14, 2016 Now then guys and Dolls, First forum post that I've had to make, after following a load of tuts and videos etc from here so first off HUGE THANKS TO EVERYONE FOR THEY'RE HELPI have a full set up going very smoothly, HOWEVER, here it is I just recently added PCSX2 for PS2 playing, it's working perfect loads up, plays on 100% BUT for the life of me I cannot get it to exit out of HS, usually I have "Esc" as my exit key but it doesn't register or rather it does but it only closes the ACTIVE HS game window and leaves the Emu running in the foreground which I then have to exit manually and click back into HS. Is there a work around for this, is there something I'm missing......... I have tried using my Google Fu to find a solution and so far I am drawing a blank, other a forum post about exiting some code but it's very poorly explained so is a much use as boobies on a fish! Any help or advice would be gratefully appreciated MUCH LOVE AND KEEP ON GAMING JBVO
albert_c Posted February 15, 2016 Posted February 15, 2016 Go into RocketLauncher>Global Settings and create a global EXIT key stroke command. It can be more than one keystroke and works perfectly for those that have a full setup on a joystick controlled emulation box or arcade machine. When you find great deals on Craigslist for CRT based cabs, exuberance can be a bad thing! Current status of cabs: 0/5 working as desired :wallbash:
liljohnnybravo Posted February 15, 2016 Author Posted February 15, 2016 I'll give it a whirl and let you know cheers
badboo Posted February 15, 2016 Posted February 15, 2016 I have exactly the same issue with the PCSX2 that I recently configured, I will give it a try when I get home as instructed by albert_c. lilijohnnybravo, please let us know if this worked for you too
Awakened Posted February 15, 2016 Posted February 15, 2016 Launch PCSX2 with the -nogui parameter. If you're using the latest stable release of the emulator, it will exit fully when you press ESC.
badboo Posted February 16, 2016 Posted February 16, 2016 Launch PCSX2 with the -nogui parameter. If you're using the latest stable release of the emulator, it will exit fully when you press ESC. Actually this works!!! Just one question, have you or anybody found any trouble when you play a game after you activate the nogui parameter? because it says in the info that it is recommended to leave it as default. Well I tried a few games for a few minutes and they ran pretty well. So far for me it is working well. Thanks for advise!!!
Awakened Posted February 16, 2016 Posted February 16, 2016 There used to be an issue in PCSX2 where it would stay running in your task manager after exiting when you used the -nogui parameter. That was fixed quite awhile ago in dev builds and that fix is now in 1.4.0. So you don't have to worry about it. They should really update that module to use it by default now.
badboo Posted February 16, 2016 Posted February 16, 2016 Oh I see, that's great then, so no worries about. The Rocketlauncher team should update it then hehe Ok awakened, thanks for the info. Cheers
saejansen Posted March 9, 2016 Posted March 9, 2016 Actually this works!!! Just one question, have you or anybody found any trouble when you play a game after you activate the nogui parameter? because it says in the info that it is recommended to leave it as default. Well I tried a few games for a few minutes and they ran pretty well. So far for me it is working well. Thanks for advise!!! I'm sorry for the noob question but i'm having the same problem. How do you exactly activate the nogui parameter?
SkyHighGam3r Posted March 9, 2016 Posted March 9, 2016 Launch PCSX2 with the -nogui parameter. If you're using the latest stable release of the emulator, it will exit fully when you press ESC. If you do this though, how do you change video/emulation settings when you boot up a game? ie. Champions of Norrath needs to be in software mode to run properly, but WinBack needs to be in hardware mode. the only way I've been able to address the necessary changes is after booting a game, alt+enter over to the GUI and change them manually, then alt+enter back to the game.
Awakened Posted March 9, 2016 Posted March 9, 2016 If you do this though, how do you change video/emulation settings when you boot up a game? ie. Champions of Norrath needs to be in software mode to run properly, but WinBack needs to be in hardware mode. the only way I've been able to address the necessary changes is after booting a game, alt+enter over to the GUI and change them manually, then alt+enter back to the game. I haven't tried it in PCSX2, but you can load game specific settings with a command line parameter: http://forums.pcsx2.net/Thread-Auto-Boot-and-Pre-Configure-Games-Separately
SkyHighGam3r Posted March 9, 2016 Posted March 9, 2016 You could have 2 emus, one set to hw the other to sw and set alternate emus in RLUI. Or you could do some custom scripting via the User Functions feature of RL to modify the necessary ini files when certain games are launched. I haven't tried it in PCSX2, but you can load game specific settings with a command line parameter: http://forums.pcsx2.net/Thread-Auto-Boot-and-Pre-Configure-Games-Separately ....O.O *bookmark page* I'm going to have to dive into this head first in a few months when I circle back to my PS2 wheel lol. That's amazing, thanks guys!
mhermann Posted September 14, 2016 Posted September 14, 2016 Been trying to get this to work most of the day. I have read through both new and old posts. I am on Windows 10, and PCSX2 v1.5.0-dev (if all else fails maybe revert back to 1.4) I played with and finally got the right version of Daemon tools working. I can load the first game and with nogui set to true it will exit without issue, but PCSX2 is remaining on in task manager. When I exit hyper spin even my mouse cursor is gone until I kill it. Can I add to the script kill the process after I exit it?
badboo Posted September 14, 2016 Posted September 14, 2016 Use the "escape" key on your keyboard only to exit. When you use the controller it glitches. Don't know why yet.
mhermann Posted September 15, 2016 Posted September 15, 2016 That is what I am doing. I can actually launch the first game upon starting hyperspin. The problem does not start until I exit the first game and try to load another one. But thanks for the quick reply.
mhermann Posted September 15, 2016 Posted September 15, 2016 Ok found the answer here: http://www.rlauncher.com/forum/showthread.php?1674-PCSX2-Module-Error-Please-help/page3 Had to modify my AHK module script
badboo Posted September 15, 2016 Posted September 15, 2016 So, can you exit with your controller now?
johnugamer Posted September 15, 2016 Posted September 15, 2016 Just wanted to chime in and say that I've been trying for weeks to get pcsx2 to exit using rocketlauncher's exit key button that I have mapped to my 360 pad. If anyone has a solution I'd love to hear it.
Recommended Posts
Archived
This topic is now archived and is closed to further replies.