Support
Having problems with HyperSpin? You've come to the right place!
4,029 topics in this forum
-
- 8 replies
- 125 views
I have a ArcadeVga video card and a 25" WG arcade monitor. When I run my ext Hd with Hyperspin running Mame games it works from the DVI port to a computer monitor. When I connect my Arcade monitor my Hyperspin comes up shows my mame games on the wheel but when I select a game the screen flashes and it remain on the game selection screen. I installed the lastest drivers from Andy and Im not sure what to try. Some of the other emulators work in HS. I first had setup my computer with XP and found that Mame worked but my other emulators would not! For XP I had to turn off hardware acceleration for videos to work in HS If anybody has any ides let me know.
Last reply by Metalzoic, -
- 5 replies
- 94 views
Hey guys, I've been up for hours and cannot seem to exit hyperspin frontend.. I have used HyperHQ and set exit as escape key. This is what I've done in short: Changed all the emulator execution to Normal instead of Hyperlaunch as the letter Q on my tankstick was disabled when set to Hyperlaunch - Letter Q was fierce punch in street fighter for example. - In doing so, it fixed the problem in game play and now I can use the letter Q on my tankstick I can exit every emulator in gameplay in HS by pressing ESCAPE button, but cannot seem to exit to the desktop.. its as if exiting HS has been disabled when I switched the execution to Normal?? I know I can chang…
Last reply by Punchout, -
- 3 replies
- 100 views
How do I run an excitable file before each start of a mame game. The file changes the resolution of windows before the game does. I am having issues with directdraw switching from interlaced to noninterlaced in windows 7. I have windows/HS set to 640x480 interlaced. This excitable will switch it to 640x288 non interlaced before the mame game switches to its resolution and had the directdraw issues. Btw This is with an Arcade monitor
Last reply by actman, -
- 5 replies
- 93 views
I have followed this guide on 3 systems. http://www.hyperspin-fe.com/best-content/ Two systems work fine The third system will not work. Issue when I run hyperspin I goto mame and no roms are listed when I press the enter button I see a HS logo on the back ground and that is it. Even tried copying my complete Dir to the machine that will not work still getting the same issue... and ideas Thankyou for reading
Last reply by syborfical, -
Who's got a spinner? (not in cabinet). I've been twitching everytime I pass by Arkanoid on the wheel because I spent a tonne of quarters on that game back in the day. Anyone ever hook up one of these to their pc? Are there link converters (to USB) available for these? Or any other ideas on a good control for this game? I suppose the mouse-scroll could be a better option than a joystick but still wouldn't give that natural feel.
Last reply by Spawk, -
- 5 replies
- 84 views
Hi all, I have a 4 player cabinet with an Ipac system. The problem im having is that when im playing 4 player games, sometimes one of the other players will press a combination of buttons that exits MAME. Is there any way i can stop this happening? Can i make just ONE combination of keys exit HS? Thanks all.
Last reply by Spawk, -
- 5 replies
- 139 views
Hey Guys, I have my setup pretty much done now... thanks to everyone for your help. I am sure that I will continue to tweak things and it will never be done 100%. I was wondering if there was a add-on or way to search for games within HS???
Last reply by rastan, -
- 10 replies
- 112 views
Hi. Next to my Xbox360 wired Joypad I'm trying to configure my Madcatz Street Fighter IV Fighstick. It works flawlessly within the emulator. But when I start Hyperspin, the wheels keep spinning and going berzerk. I can't even exit out of it. it just keep spinning and spinning. Is there a change to get the stick working in hyperspin? I haven't got a clue about vjoy, joy2key or something like that. Just don't let me use xpadder please. any help is greatly apprectiated. Tom
Last reply by Rincewind, -
- 6 replies
- 103 views
Sorry if this is the wrong place for this topic, it's a HyperSpin question but it is also related to all things run in HyperSpin (Retroarch, RocketLauncher, Mameuifx etc) I am having a heck of a time with controllers and controls. I set them up int he appropriate spots and they work great, but often windows will then reassign a controller which then breaks everything. Example is say I have an Xbox Controller and a PS2 controller hooked up. I set them up and Xbox is controller port 0, PS2 is port 1. Everything works fine but if I unplug them or reboot (or a myriad of other things that will cause them to change) sometimes they switch ports. Even though I didn't swit…
Last reply by Spawk, -
- 1 reply
- 122 views
So I'm sure I asked this before but forgot the answer. When I have my bezel turned on my task bar shows up when the games launch. Is there a way for that not to happen?
Last reply by griffin518, -
- 3 replies
- 75 views
I just setup a Taito Type X wheel and i have one game in it SFIV. when i enter the wheel i get a list of the one game SFIV ...fine. Upon spinning the wheel however the art turns to the standard blue text instead of the SFIV logo any ideas why this would happen? Cheers
Last reply by CarloCGC, -
- 0 replies
- 101 views
So I know I can download Hyperlists from the website and I know you can then use HyperTools to exclude items from showing in your wheel. My confusion is when it comes to Clrmame, RomCenter, Romlister, etc. Not sure if any of the tools do what I want, but I built my own sets with Clrmame 1G1R sets. The issue is there is no way to load that data into a Hyperlist..I have googled for hours and tutorials and all and to no avail. Not sure if what I am trying to do is even possible. I like Clrmame becaues it's very easy to fix files, rename files, remove uneeded and filter regions or prioritize regions..but again I've found no way to use that with Hyperspin, other t…
Last reply by NewYears1978, -
- 4 replies
- 95 views
Pinball FX2 uses my xbox triggers to play. I have the front right trigger set as an alternate exit key. Is there a way to not have it set to that for Pinball FX2 only? I am not sure.
Last reply by demonseed, -
.thumb.png.e802418a5006739fd2dcbfa24bab8f2b.png)
- 1 reply
- 76 views
Morning fellow Arcadian's Currently got my HTPC setup running: I have recently installed my first HS setup from scratch following the great tutorials on here and now have the following setup configured: HyperSpin v1.4 RocketLauncher v1.0.1.4 RocketLauncher UI v1.0.0.9 + Using JoyToKey v5.8.0.360 [Registered] + MS Xbox 360 Controller +Currently setup up - Commodore 64 Wheel using [WinVice] All the above is working great. Hyperspin launches fine, JoyToKey launches [HYPERSPIN] profile which functions perfectly with Xbox 360 Controller. I select the Commodore 64 wheel > Game of choice (All work through WinVice standalone and also from RocketLaunc…
Last reply by Spawk, -
- 8 replies
- 133 views
I recently formatted and did a fresh install of Windows 7 and copied over my entire Hyperspin to this drive to use as backup for when my main drive fails. When opening HyperHQ everything is distorted and illegible. Also, Hyperspin seems to open (the icon appears at the bottom of the screen) but it doesn't open on my monitor. It's as if it is going to another monitor. I only have one monitor connected and my settings don't indicate otherwise. Any idea of what is going on here and how I can correct it. Thanks.
-
- 1 reply
- 99 views
Hi, I have setup a clean install of hyperspin 1.4 and rocketlaucher. The games are starting inside rockerlauncher, but they are not starting inside hyperspin or hyperlaunch. Below the log of hyperlaunch: 09:40:54 | HyperLaunch v2.25c 09:40:54 | System Specs: HyperSpin Dir: D:\HyperSpin OS: WIN_7 OS Language: 0413 OS Admin Status: No Monitor #1 (\\.\DISPLAY3): 1366x768 (1366x768 work) HyperSpin Res: 1025x556 AHK Version: 1.1.07.03 09:40:54 | HyperLaunch launched directly 09:40:56 | HyperLaunch received "MAME" and "1on1gov" 09:40:56 | INI Keys read 09:40:56 | Possible duplicate launch. is already running, closing HyperLaunch It is menti…
Last reply by quile, -
Hello anybody! I have a device that I want to use like mouse in hyperspin application. But the problem is that it give (x,y) location on the screen, not (delta x, delta y). Can I use it anyway? or it is impossible for hyperspin? I'm just choosing an implementation for my idea, could you help me? Thanks in advance!
Last reply by kirill702b, -
- 1 follower
- 2 replies
- 121 views
Hi Guys Forgive me if there is an easy answer for this. I'm basically a beginner, even though I've been here a while, and I've only survived by following tutorials to the letter. So please be gentle with me. I am using MAMEuifx .153 (as I got all my downloads etc from the Simply Austin youtube tutorial, so I just followed his lead). I've got everything running perfectly, which is awesome because I tried it on my own and it ended in tears once before. But my problem is this: When I launch a game in HS, the title screens and game play is very pixelated. Just to make sure it's not a problem with my system etc, I have launched the same games in MAMEuifx and a…
Last reply by Skeeball_Fanatic, -
- 0 replies
- 65 views
So, I am almost done my setup.. couple bugs but almost there.... Kat5200 is causing me grief and I do not understand why. In rocket launcher I test a game and it loads and exits fine. In HS, it flashes a command box then kicks back to HS..?? Any ideas? thansk so much in advance. 22:22:42:140 | RL | INFO | +N/A | Main - RocketLauncher v1.0.1.4 (www.rlauncher.com) 22:22:42:140 | RL | WARNING | +0 | Main - You have "Logging_Log_Command_Window" enabled. This is only for logging errors being dumped to the command window from an executable. This may cause issues with running some executables and needs to be turned off when you are done. 22:22:42:370 | RL | …
Last reply by demonseed, -
- 4 replies
- 92 views
Good morning friends, I'm making a new installation of Hyperspin 1.4 0 + RL. I am using emulators he had in the previous version of HS. For I have found problems with the emulator CPS3. From outside HS it works correctly, since RocketLauncherUI also works, but since HS, the emulator appears but does not load any game and this HS background and not charge anything. In the log I can see is called the emulator + rom name. If I run it from a "cmd" I open the game smoothly. You know that it may be due? Frontend and use the Plugin "HyperSpin" Thank you. A greeting.
Last reply by Metalzoic, -
- 10 replies
- 373 views
New user here, so if this has been answered before please point me in the right direction! I've been tinkering with Hyperspin for a month or so now and almost have it where I want it. I really like the Arcade Classics genre wheel in MAME and would like to add it to the Main Wheel, which I have done without an issue. My issue is getting all of the media to carry over. The Hypersync utility doesn't have a selection for arcade classics so I can't just download the preferred media files. Since the files already exist in the MAME media folder, is there a way to point the Arcade Classics wheel to that media folder rather than it's own empty folder? I was lo…
Last reply by rastan, -
- 2 replies
- 78 views
When i run PCSX2 through Hyperspin and RocketlauncherUI the fade screen stays up even though the emulator is running behind it, eventually i get this message: Any help with this greatly appreciated
Last reply by rastan, -
- 3 replies
- 117 views
other than manually setting each one up... is there a easy way to setup multiple programs to use the same profile? or a way to do this in RL?
Last reply by rastan, -
- 6 replies
- 174 views
Hello, Is there a place on this site that tells you what emulator to select/install in order to emulate a particular console or an arcade machine ? For example I am looking to set up Capcom Play System I, II and III but I can't figure out which emulator to use (or which version of the emulator to use). I can't find any videos on this either that are in English... Thanks for the help !
Last reply by rastan, -
- 3 replies
- 85 views
I am hoping someone can point me in the right direction. Here's the setup: Laptop with hyperspin and Rlauncher using HDMI pointed to a projector and using 2 xbox 360 wireless joysticks. All my systems, atari, mame,neo, etc work great! I started installing pc games and steam games that work natively with the 360 controller like fallout 3,rust, geometry wars. A friend told me you could use the 360 controller as a mouse and I thought Pop cap would be a good fit but... Everygame starts minimized with JoytoKey (which is what I use for controlling hyperspin) So i switched to Xpadder and most, not all of the popcap games launch minimized. I set the prog…
Last reply by Spawk,
-
Popular Contributors
